Wednesday, 23 September 2015

Our Generation RV Camper for American Girl Dolls or 18 Inch Dolls ~ Makeover

Our Generation RV Camper for American Girl Dolls or 18 Inch Dolls ~ Makeover

Inspired by some lovely pictures of OG Campers from Our Generation / Battat we've seen on Pinterest, we've had a go ourselves to make it a little bit more cheerful.
Our Generation RV Camper Makeover

Curtains

The existing curtains in OG RV Camper are non removable, so to change them, you'd need to cut them off. The new ones I've made are designed to be removed, so you could, e.g. remove them for washing, or have a different set for different seasons!
Finished size 4"x6"
Make 4:
Cut fabric  4.5" x 8"
Fold under 1/4" inch and top stitch the edges to stop it from fraying

Sew on thin strips of velcro (hook & loop tape, I cut it in half lengthwise so it's thinner) at the top end (on the "wrong/back side" of the fabric" 1.5" apart (as measured on the outside) as it needs to go around the rails to hang on

Note - I made new curtains slightly longer then existing ones, and just simply tied them with thin 4mm ribbons

Before : Left Window ~ After : Right Window


Cushions

Make as many as you wish - we've made 6. We used matching fabric and left one of the original pillows. We made our own inserts for the pillows by cutting dress lining fabric - 2 squares 4"x4" for each pillow, and stuffing them with toy stuffing and sewing shut. Pillowcases are removable for washing.

For cushion covers:
Finished Size 4x4"  - cut 4.5" x 4.5" fabric square for pillow front, and 4.5" x 6.5" for pillow back (cut into 2 parts at 3.5" & 3"), so you end up with 3 pieces like that:

Turn under 1/4" of the longer side of the two "back" pieces and top stitch to stop it from fraying:

Put the fabrics the right way together - the big square at the bottom, and on the top, the longer rectangle overlapping the shorter one, like so (so shorter back piece is below the larger one):

Sew all the away round (I use 1/4" seem allowance for all doll size sewing), leaving a gap for turning inside out (the right way out). I use a wooden point turner to "finger press it" and push the corners out. 

Now you can put the pillow inserts into your pillow cases. 



Duvet Cover

To make a cover for the "duvet" that comes with OG Camper, which is roughly 7x13", I cut the 9.5" x 15.5" for the front, and two pieces for the back = 2" x 9.5" and 14 3/4" x 9.5"

It's made exactly the same as the pillow cases, except this cover is "Oxford style" so after turning it the right way out, I top stitched all the way round about 5/8" away from the edge to create a decorative "flap"



Under sink curtains

Just like the curtains, you can't take them off, they need to be cut off. You could leave it as open space, so the shelves show, or add the curtain. The sewing is similar to the curtains - cut 8" x 9.5", top stitch 1/4" under all the way round, and sew velcro / hook & loop tape 1/4" thin along the side 2.5" apart (outside measurement). You may need to use tweezers (or small screwdriver or flat tool) to push the fabric around the rails, it's a bit of a tight squeeze.

Tea Towel

Cut 5 1/4" x 8" fabric, fold in half, right way together. Stitch 3 sides, leave short one open, turn the right side out, and top stitch all the way around, closing the gap.

Table Top Cover

Finished size 5 1/4" x 3.5"
Cut 7" x 5 5/8", fold 1/4" under on short edges and top stitch them, and then fold in half along long edges that are NOT top stitched (right way together) and sew along those two edges only. Turn right side out and slide onto the table. You can also cut a matching piece of fabric to lay on the worktop behind the "table top".


Please do not repost these instructions, but you may link to this post. Thank you!
You can watch the final result on our channel:








No comments:

Post a Comment

Related Posts Plugin for WordPress, Blogger...